Re: molnar cranks
[Re: mopar dave]
#1434406
05/11/13 01:02 PM
05/11/13 01:02 PM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
Very good pieces for the money. I have been dealing with them almost since day one of the old K1 days, and have always liked their stuff. They are a good value, and I use and sell them with confidence...
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: molnar cranks
[Re: CompWedgeEngines]
#1434407
05/11/13 04:25 PM
05/11/13 04:25 PM
|
Joined: Jan 2003
Posts: 74,970 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,970
U.S.S.A.
|
Quote:
Very good pieces for the money. I have been dealing with them almost since day one of the old K1 days, and have always liked their stuff. They are a good value, and I use and sell them with confidence...
This , if a person can only afford a CCJ crank then this is the Crank to buy , unlike many others , this one is ready to run, and if it's not you won't get a song and dance or told to scrape bearings to make it work .
|
|
|
Re: molnar cranks
[Re: lowflyingdart]
#1434411
05/14/13 10:48 PM
05/14/13 10:48 PM
|
Joined: Nov 2004
Posts: 287 Michigan
SC304
enthusiast
|
enthusiast
Joined: Nov 2004
Posts: 287
Michigan
|
Quote:
Quote:
Tom Molnar started/owned K1. He then sold it to Carrillo, and started Molnar Technologies.
Before K1 Tom ran Oliver, when he left there, they stopped building crankshafts. You will not find a better crank for the money or better customer service than Molnar Tech.
never had an issue with Toms products. I run them in my Gen 3 Super Stocker and have had zero issues. Very Knowledgeable and friendly on the phone.
Mike
|
|
|
Re: molnar cranks
[Re: mopar dave]
#2583640
11/27/18 12:38 PM
11/27/18 12:38 PM
|
Joined: Jul 2010
Posts: 2,422 Pittsburgh PA
Eric
top fuel
|
top fuel
Joined: Jul 2010
Posts: 2,422
Pittsburgh PA
|
Molnar in the Arrow also....Mike Janis built my mill and said it was a very nice piece.
5.53 @ 125 1/8th on the launch control..more left in her!
|
|
|
Re: molnar cranks
[Re: Eric]
#2583656
11/27/18 01:12 PM
11/27/18 01:12 PM
|
Joined: Dec 2013
Posts: 4,664 Wichita
GY3
master
|
master
Joined: Dec 2013
Posts: 4,664
Wichita
|
I have over 5,500 street miles and 100's of 1/4 mile passes on my 4.25 BB Molnar crank and 7.1" rods. My machinist sees a lot of different brands and was very impressed with the quality. Crank and rods needed NOTHING (he's picky, too!) and everything balanced easily.
'63 Dodge 330 11.19 @ 121 mph Pump gas, n/a, through the mufflers on street tires with 3.54's. 3,600 lbs. 10.01 @ 133mph with a 250 shot of nitrous an a splash of race gas. 1.36 60 ft. 3,700 lbs.
|
|
|
Re: molnar cranks
[Re: mopar dave]
#2583679
11/27/18 02:33 PM
11/27/18 02:33 PM
|
Joined: May 2005
Posts: 1,030 ohio
67mprfan
super stock
|
super stock
Joined: May 2005
Posts: 1,030
ohio
|
That's good to hear because I couldn't resist cyber Monday deals and ordered a crankshaft from Mancini
71 demon stock stroke 440/indy ez-1 running 10.10 @ 132.14 mph in the 1/4 and 6.36 @ 107.46 mph in the 1/8 not in the same weekend but It did it then I sold it. 67 Belvedere that worked it's way in the 10's
|
|
|
Re: molnar cranks
[Re: 340Cuda]
#2583814
11/27/18 07:33 PM
11/27/18 07:33 PM
|
Joined: Jul 2010
Posts: 2,422 Pittsburgh PA
Eric
top fuel
|
top fuel
Joined: Jul 2010
Posts: 2,422
Pittsburgh PA
|
While I have not purchased a crank from Molnar I have purchased a couple of sets of rods.
I have great respect for Tom Molnar and would not hesitate to buy anything that he sells.
He is a stand up guy for sure...and a dog lover which makes him excellent in my book
5.53 @ 125 1/8th on the launch control..more left in her!
|
|
|
Re: molnar cranks
[Re: racerx]
#2584042
11/28/18 04:16 AM
11/28/18 04:16 AM
|
Joined: Jan 2003
Posts: 2,932 Finalnd, Perkele
jyrki
master
|
master
Joined: Jan 2003
Posts: 2,932
Finalnd, Perkele
|
I have used them in boosted application. Zero problems with the crank. Calculated 1660hp.
Plynouth VIP '67 TT IC EFI
|
|
|
Re: molnar cranks
[Re: mopar dave]
#2584080
11/28/18 10:59 AM
11/28/18 10:59 AM
|
Joined: Jan 2003
Posts: 15,439 Val-haul-ass... eventually
BradH
Taking time off to work on my car
|
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
I hear the molnar cranks are made in china... I think there are only a few companies today whose crankshaft forgings DON'T come from China, and those places don't sell BBM cranks for much under $2K, IIRC.
|
|
|
|
|