Harland Sharp rockers and stock valve covers? - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Harland Sharp rockers and stock valve covers?

Print Thread

Harland Sharp rockers and stock valve covers? #1101038 10/24/11 08:50 PM 10/24/11 08:50 PM
Joined: Oct 2004 Posts: 1,946 Connecticut 5126brl No more OP top fuel
5126brl No more OP top fuel Joined: Oct 2004 Posts: 1,946 Connecticut	Looking into getting a set of H/s rockers " 1.6" ratio and heard that they may not fit under a stock steel valve cover? Anyone know the facts on this? Thanks

Re: Harland Sharp rockers and stock valve covers? [Re: 5126brl No more] #1101039 10/24/11 08:51 PM 10/24/11 08:51 PM
Joined: Jan 2003 Posts: 3,103 Phila Pa S scatpacktom master
scatpacktom master S Joined: Jan 2003 Posts: 3,103 Phila Pa	They fit.

Re: Harland Sharp rockers and stock valve covers? [Re: scatpacktom] #1101040 10/24/11 09:02 PM 10/24/11 09:02 PM
Joined: Oct 2004 Posts: 1,946 Connecticut 5126brl No more OP top fuel
5126brl No more OP top fuel Joined: Oct 2004 Posts: 1,946 Connecticut	Thanks Tom,

Re: Harland Sharp rockers and stock valve covers? [Re: 5126brl No more] #1101041 10/24/11 09:53 PM 10/24/11 09:53 PM
Joined: Jan 2003 Posts: 20,740 A collage of whims topside Too Many Posts
topside Too Many Posts Joined: Jan 2003 Posts: 20,740 A collage of whims	On mine, I had to bevel the corners of the hold-downs at both ends, and ball-peen some clearance at the oil baffles. That's with the 1.6 HS setup on Eddy heads. Wasn't a big deal, but I about had a heart attack first time I heard the racket.

Re: Harland Sharp rockers and stock valve covers? [Re: 5126brl No more] #1101042 10/24/11 10:27 PM 10/24/11 10:27 PM
Joined: Mar 2004 Posts: 314 Medina, OH D dart440_72 enthusiast
dart440_72 enthusiast D Joined: Mar 2004 Posts: 314 Medina, OH	Mine fit as well. No problems.

Re: Harland Sharp rockers and stock valve covers? [Re: dart440_72] #1101043 10/24/11 10:34 PM 10/24/11 10:34 PM
Joined: May 2011 Posts: 4,489 northern,Ohio,USA C Clanton master
Clanton master C Joined: May 2011 Posts: 4,489 northern,Ohio,USA	you can get some clay from a craft store and chech by cycling thru the lift.i did not have a problem with the taller covers[1973 up i think] GOTBOOST!New improved with Victor heads. http://www.enginelabs.com/mopar-big-bloc...t-of-necessity/

Re: Harland Sharp rockers and stock valve covers? [Re: 5126brl No more] #1101044 10/24/11 11:18 PM 10/24/11 11:18 PM
Joined: Nov 2004 Posts: 3,544 Syracuse,NY CompWedgeEngines master
CompWedgeEngines master Joined: Nov 2004 Posts: 3,544 Syracuse,NY	Most often they fit, there does seem to be some slight differences in some stock valve covers...as mentioned, sometimes its just the corners and or baffles. I can take care of you on Harlands, drop me a PM or email if you wish.... RIP Monte Smith Your work is a reflection of yourself, autograph it with quality. WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.

Re: Harland Sharp rockers and stock valve covers? [Re: CompWedgeEngines] #1101045 10/25/11 02:04 AM 10/25/11 02:04 AM
Joined: Jan 2003 Posts: 27,421 Balt. Md 3 383man Too Many Posts
383man Too Many Posts 3 Joined: Jan 2003 Posts: 27,421 Balt. Md	I wanted stock looking covers as I wanted the Max Wedge look so I used these which I think are old Eddy valve covers. They were chrome but scratched which I did not care as I was painting them orange anyway. They look a bit taller then stock but look close to stock to me. I use Hughes 1.6 roller tip rockers with .630 lift on my 63's eng and they work fine. Ron Last edited by 383man; 10/25/11 02:05 AM.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1