Moparts Forums >> Moparts Question and Answer

Pages: 1
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
FAST #170634 O2 Sensor Kit Install
      #6482064 - Fri Feb 18 2011 05:45 AM Attachment (66 downloads)

After thinking about this for over a year, I finally settled on the FAST #170634 analog A/F kit. This kit comes with the gauge (bracket not included), harness, and a single O2 sensor.
I was looking for something simple and less expensive that I could mount and leave it alone for my street car. A couple of years ago when I put on the headers, I located the bungs for both sides and had them welded in. Now that I finally got around to buying the kit, the O2 sensor went right in with no interferences. I currently have it mounted on the drivers side and hopefully down the road I will buy a second one for the passenger side.
So far the install is going smooth. The location for the drivers side O2 sensor worked out so that I can route the harness straight up to the floor where the 727 linkage comes thru. There is a rubber boot there around the shaft which allowed me to run the harness thru and then I added silicone to seal it up tight from water or dirt. This landed the end of the harness/O2 sensor connector just inside of the car which is located under the center console. This allowed me to mount the processor under the center console where it is hidden from view. Then I rolled up the harness under the carpet and ran it forward towards the fire wall. Now I can mount my gauge and run all of the wire up and under the dash where everything is still hidden from view.
I still need to wire in the gauge but so far this kit is very simple to install. I should have the wiring buttoned up this weekend. If you are looking for a lesser optioned O2 sensor kit, check out the FAST #170634.

--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
Re: FAST #170634 O2 Sensor Kit Install [Re: YO7_A66]
      #6482067 - Fri Feb 18 2011 05:47 AM Attachment (67 downloads)

The first picture shows that the clearance is fine to run up to two sensors with a 727.
This picture shows where the sensor cable goes up thru the floor shifter linkage boot with no cutting involved.

--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
Re: FAST #170634 O2 Sensor Kit Install [Re: YO7_A66]
      #6482068 - Fri Feb 18 2011 05:49 AM Attachment (64 downloads)

This picture shows the processor mounted under the center console area. This hides it and keeps it from sliding around.
This post is just meant for a reference to those of you considering the O2 style kits. Sorry for the dark photos, but they were taken with my cheapie phone camera.



--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
Re: FAST #170634 O2 Sensor Kit Install [Re: YO7_A66]
      #6482071 - Fri Feb 18 2011 05:57 AM Attachment (71 downloads)

This is the wiring schematic that comes with the kit. It is very clear and easy to follow.

--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
Re: FAST #170634 O2 Sensor Kit Install [Re: YO7_A66]
      #6482098 - Fri Feb 18 2011 06:24 AM Attachment (61 downloads)

This is the kit.

--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
astjp2
master


Reged: Jan 18 2011
Loc: Utah and Alaska
Re: FAST #170634 O2 Sensor Kit Install [Re: YO7_A66]
      #6483701 - Fri Feb 18 2011 10:54 PM

OK, How well does it work? I need to get one for my jeep to tune the stroker in it. Tim

Post Extras: Print Post   Remind Me!   Notify Moderator  
DaytonaTurbo
I Could Care Less...But I'm Not Going To


Reged: Feb 26 2003
Loc: Manitoba, Canada
Re: FAST #170634 O2 Sensor Kit Install [Re: astjp2]
      #6483777 - Fri Feb 18 2011 11:41 PM

I run an Innovate LC-1 with an analog gauge. Looks to be basically comparable to what you have. Works great, no problems.

--------------------


Post Extras: Print Post   Remind Me!   Notify Moderator  
YO7_A66
master


Reged: Jan 20 2003
Loc: Indiana
Re: FAST #170634 O2 Sensor Kit Install [Re: astjp2]
      #6484103 - Sat Feb 19 2011 08:35 AM

Tim,
I should be able to finish the gauge wiring next week and then once our weather decides to turn for the better, I will get the car out and start tuning with it.

Thanks

--------------------
1970 YO7 A66 [Canadian Export] F8 Challenger
340(SL.P. 226/238@.050,270/288 dur,.489/.480" 112 deg., 9.7:1, 2.02's),RPM intake, QF SS-750 Annular DP, MSD Street Fire Ign., & TTI's. 727(built by Rick Allison) /Dynamic 9.5" 3800, TF-2, & A&A 5600rpm Hemi gov.)& 3:91's (235/60's & 255/60's).


Post Extras: Print Post   Remind Me!   Notify Moderator  
Pages: 1



Extra information
6 registered and 52 anonymous users are browsing this forum.

Moderator:  moparts, SanityLost, tboomer, LTDan, 70Cuda383, Hotwheelsjr, not_a_charger, Eric, Al_Alguire 

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 777

Rate this topic

Jump to

Contact Info | Privacy statement main index

Powered by UBB.threads™ 6.5.2