John Fan
member
Reged: Oct 27 2008
Loc: Michigan
|
|
Post deleted by not_a_charger
Edited by John Fan (Tue Nov 03 2009 04:16 PM)
|
redcudaracer
member
Reged: Oct 26 2007
Loc: Maryland,Harford Co.
|
|
MOPAR RACE STUFF
Aarospace Comp 400 fuel pump mock up never used
new $415 SELL $275 + ship
Barry grant 4 port reg used $120
parts Barry grant 4 port reg(mis diaphram)$50
Barry grant 2 port used $65
Holley big 2 port reg $40 sold
Russel Pro fuel filter used w/new cartrige $50
call Paul 443 506 0912
Edited by redcudaracer (Thu Nov 19 2009 07:13 AM)
|
redcudaracer
member
Reged: Oct 26 2007
Loc: Maryland,Harford Co.
|
|
More Mopar race stuff
B1 CAST TUNNEL RAM FOR RB dom flange $500 firm
Zeeker cast tunnel ram fits zeeker heads also told
fits indy-1 heads dom flange $250
CCM 9 inch converter 20 runs for 727 5500 stall
behind my 556 ci $500
CSR glide full trans shield sfi jan 07 $200
B1 orignals complete rockers,shafts,spacers used 1.7 ratio .1 broken rocker (int) $200
Restored 70 71 duster grill w/headrings nice $400
|
72sat
member
Reged: Mar 10 2004
Loc: St.Louis ,Mo.
|
|
SOLD THANKS MOPARTS!!!!!!!!!!!!!
Edited by 72sat (Thu Nov 05 2009 02:33 AM)
|
1BaadBee
member
Reged: Jan 20 2003
Loc: Marion, IL
|
|
I have a new, unused in the box aluminum Summit radiator #380428 $130.00 Contact me at richm43@verizon.net Thanks Moparts
|
QWK_ENUF_on_ E85
top fuel
Reged: Sep 20 2005
Loc: USA
|
|
******SOLD******
nice used TM-6 single plane intake for 383 or any low deck
not cut or altered
$100.00 plus shipping
NW indiana
PM me
--------------------
CRT
Mendez Motorsports
Edited by QWK_ENUF (Thu Nov 05 2009 09:35 PM)
|
joez
super gas
Reged: Jan 20 2003
Loc: PA
|
|
528 Low deck Indy block, B1MC oval port heads, MP 4.15” crank, Grp rods, Diamond pistons, calico bearings, Hellfire rings, Straight line roller cam, T&D individual shaft rockers with pushrod oiling, Jesel Belt, NRC offset dist, Petersen wide vac oil pump, aluminum rear sump oil pan, meziere water pump, Sheet metal intake with 2 Kinsler throttle bodies, Ford Motorsports 160lb/hr injectors, two dry stages of nitrous, FAST engine management with all options and Applied Nitrous Jeff Prock firmware. Best performance was 8.20 @ 171 in a 3050lb small tire car using one stage. Pistons, rings, bearings are new, 35 runs on rods, motor is disassembled, will assemble, $15,000 obo no trades,
Will separate, Complete manifold with nitrous and all fast harness and computer $3000. Motor less manifold and fuel injection $12,000.
nitrojoez@yahoo.com
|
Dunnuck Racing
mopar addict
Reged: Mar 18 2007
Loc: Moparts Detention
|
|
Cam Dynamics #CD278/284 RA(P4007278Mopar)S.B.
Roller cam 278/284@.050 620/640 lift $150.00
Holley Street Dominator intake#300-7 Dirty but in good shape,318 sized ports SALE PENDING....................... $40.00
B.B. Weiand 7512 intake,decent shape $60.00
B.B. Comp Cams roller cam #CRB-308-8-308-8r106
280/280@.050 .440/.440 lobe lift *****SOLD******
Jeg's Dominator air cleaner,chrome housing,hi-flow element mock up only $30.00
K&N stub stack for 4500 series ******SOLD*****
All parts are used,plus actual shipping charges.
Please P.M. me here.
Thanks for the ad space,Moparts! 
--------------------
Vic Bloomer Cylinder Heads sponsored
421 small block 1970 Dodge Challenger
Using a Bloomer Performance Engineering
(Rod Bloomer)4.125 stroker crank
10.21 @131.13..........so far!
Edited by Dunnuck Racing (Thu Nov 12 2009 09:18 PM)
|
His and Her 69's
mopar
Reged: Jul 07 2005
Loc: Oh
|
|
What I have is a Brand New, Never Used, Complete pair of 440-1 Iron heads.
Here is what all I have,
A Pair of NEW Indy 440-1 Iron heads,
Stainless Valves,
Indy Rocker Arms,
Rocker Shafts,
Rocker Stud kit,
Head Oiling kit,
440-1 Intake, (4150 carb pattern)
Indy Valley Plate,
All these items are New,
I want $2200,00 for it all.
If you're interested give me a call,
Mike 419-575-2981
or e-mail David at eschedr@bgnet.bgsu.edu and he will try and connect us.
--------------------
|
Ari440
addict
Reged: Oct 15 2004
Loc: long island
|
|
35 gpm mazerie water pump $350 plus shipping
pm me
--------------------
1.45 10.20s -131 mph
|
Ari440
addict
Reged: Oct 15 2004
Loc: long island
|
|
12 gallen rci fuel cell new cap and strapes #10 lines $150 plus shipping
pm me
--------------------
1.45 10.20s -131 mph
|
Ari440
addict
Reged: Oct 15 2004
Loc: long island
|
|
crane iron rockers 1.5 with springs
needs two adjusters $150 plus shipping
pm me
--------------------
1.45 10.20s -131 mph
|
tntmachine
member
Reged: Mar 03 2008
Loc: IL
|
|
Send a P.M.
Edited by Diego_Ted (Thu Nov 05 2009 09:29 AM)
|
Gumbydammit
I'm GUMBY DAMMIT
Reged: Sep 03 2003
Loc: Lost in Pooler, GA
|
|
Competition engineering roll bar kit for A body. New in boxes, not ground on. Local pick up ( Savannah, GA )only, I don't want to bother with trying to ship it. $100 Part # CEE-3123
Summit cast aluminum valve covers for big block Mopar. New in box. Silver powder coated. includes all bolts and gaskets. $100 + shipping.
Black plastic ( phenolic ) open 4150 spacer - 2". New in box with carb studs and nuts. $20
--------------------
I'm Gumby dammit!
'68 Dart- 440, Stage 6 heads, Comp solid street roller, Mini-tubbed, yadda yadda. . .
in da woiks.
Edited by Gumbydammit (Thu Nov 05 2009 10:26 PM)
|
ValiantRich
member
Reged: Aug 30 2003
Loc: Long Island, NY
|
|
BG 400 Fuel Pump. This pump has never been used since I got it back from BG when it was checked for proper operation and new seals installed. $250 plus UPS. rich1981@optonline.net SOLD!!!
Edited by ValiantRich (Fri Nov 20 2009 09:57 AM)
|
FOOLISH_PLEASURE
member
Reged: Mar 09 2004
Loc: STERLING VA
|
|
B1/BS Heads new with rockers $1600.00
pm me here or call 703-615-6296
SOLD THANKS MOPARTS
Edited by FOOLISH_PLEASURE (Fri Nov 06 2009 09:32 PM)
|
gtea1901
member
Reged: Nov 26 2004
Loc: PORT ORANGE FL.
|
|
--------------------------------------------------------------------------------
20-Accel 276 spark plugs $20.00 new
1-set Daytona Sensors -WEGOD-8pack this is a complete set of 8 o2s that
will interface with many data loggers RacePak, Autometer, Edelbrock, RPM
new in the box $1795.00
1- Innovate Motorsport LC-1 o2 sensor new in the box $125.00
1- set Calico coated SBC main Brgs 5M909H-1 $100.00 new
1-set Calico coated SBC rod brgs 1B663H-1 $80.00 new
1-set Calico coated SB Mopar main brgs MS1344V-std $100.00 new
1-set Calico coated SB Mopar rod brgs CB481HN-std $80.00 new
1-set Calico coated BB Mopar main brgs 119M-010 $125.00 new
1-set BB Mopar rod brgs CB527P-.20 $45.00 new
1-set BB Mopar main brgs MS877P-.020 $80.00 new
1- Moroso chevy oil pump primer $10.00 new
1- ARP sbc oil pump drive $15.00 new
1- set Manley NEX-TEX 221449-16 valve springs $450.00 new
1- Cam Motion 426 Hemi flat tappet camshaft S2681/2741-110 $150.00 new
2- MSD Pro Power coils $40.00 each used
1-pair coilover springs 14 inch 110 lb. $25.00 used
1-Autometer 2 5/8 #3411 fuel pressure gauge with cup and braided line $40.00 used
1-Autometer 2 5/8 liquid filled 0 to 300 pressure gauge $20.00 used
1-Stewart-Warner 2 5/8 oil pressure gauge $20.00 used
1-Stewart-Warner 2 5/8 mech water temp gauge $20.00 used
1-set Comp 977-16 valve springs $80.00 new
1- Turbo Action 8 inch converter for 727 5500 stahl $400.00
1-set MacDowell Super Stock Hemi heads complete with Hogan sheetmetal manifold need guide work $4500.00 used
1-MSD HVC coil $50.00 used
1-set Hooiser 14x32L drag tires 12 runs $250.00
1 Dynamic 7 inch 904 converter 2 runs $750.00
call Denny Steward (717) 676-3349
or GTEA1901@aol.com 
|
105630
enthusiast
Reged: Oct 18 2005
Loc: back home in georgia ,lake sid...
|
|
B1 CFE sheetmetal intake ,with three compucar foggers complete less carbs 2400.00 buyer pays shipping
|
TheDodgeBoys
member
Reged: May 15 2008
Loc: Bowling Green, Ky
|
|
I have a set of primary metering blocks for the 4235 & 4236 Hemi Super Stock carbs. The part# is 4409 and that is the correct metering block for these carbs. They are in great shape! $100 for the pair plus shipping!
Thanks,
Allen Mansfield
The Dodge Boy's Performance
270-779-0400
mansfield_allen@yahoo.com
--------------------
"THE DODGE BOY'S PERFORMANCE 270-779-0400
1968 NSS/AA "HEMI" DODGE DART
1970 "452" E-85 PLYMOUTH DUSTER
1987 "318" RAM D100
1986 "360" RAMCHARGER (GONE)
RACER'S FOR CHRIST CHAPLAIN
NHRA DIVISION 3
"LAND OF THE WINNERS"
....AND ON THE 8TH DAY, GOD CREATED MOPARS
|
W2WHO
member
Reged: Oct 31 2008
Loc: SO. FLA
|
|
Post deleted by not_a_charger
|
Moparguy383
super street
Reged: Jan 20 2003
Loc: Cumberland, MD
|
|
SOLD!
Edelbrock TM-7 intake for sale. Never been cut on, all of the carb mounting holes have been heli coiled. It is painted high heat black. $125 shipping included in the lower 48.
Email me for pictures. If paying with paypal you will have to include the fees they charge. Thanks for the ad.
--------------------
[image][/image]
"He never hit the brakes, and he was shifting gears"
moparguy383@hotmail.com
Edited by Moparguy383 (Thu Nov 19 2009 03:28 PM)
|
Moparguy383
super street
Reged: Jan 20 2003
Loc: Cumberland, MD
|
|
SOLD!
Brand new Mopar .484 cam for a big block. It came with a car I bought, and do not have any use for it. Has all of the lifters still new in the boxes, and includes the Mopar assembly lube. This is the old school cam. $125 plus shipping.
Email me for pictures. If paying with paypal you will have to include the fees they charge. Thanks for the ad.
--------------------
[image][/image]
"He never hit the brakes, and he was shifting gears"
moparguy383@hotmail.com
Edited by Moparguy383 (Thu Nov 19 2009 03:27 PM)
|
GDonor
member
Reged: May 20 2008
Loc: Connecticut,USA
|
|
SOLD!!! indy 440 intake manifold,dominator flange,only used on the 1/4 mile,excellent shape.$175.00buyer pays shipping ,gene@1860-490-6253 
Edited by GDonor (Mon Nov 09 2009 04:59 PM)
|
69dart
super street
Reged: Jan 21 2003
Loc: Columbus, Ohio
|
|
A-body Factory Disc Brake setup. Includes everything but the spindles (Fits 73-76 Dart or Valiant Spindles) - includes Rotors, caps, 2 piston calipers, pads, lines, dust shields, racing wheel studs and hardware. These brakes worked perfect on my car. I could easily make the 1st turnoff at any dragstrip without any problems. I just converted to racing brakes to shed a few pounds.
$200
Everything together weighs in around 80 lbs so shipping could be pricy.
Also have the factory rear drum setup for a Mopar rearend. Fits 8 3/4 or Dana ends for sure. Includes Drums, pads, backing plates and hardware.
$100
FInally I have a Helicoil kit to repair stripped Holley Card Bowls Screw Threads. This is the 12-24 kit Includes Tap and Insert Tool and Several Helicoils.
$20 shipped to you SOLD
email me at bemiller@insight.rr.com
Located in Columbus Ohio
--------------------
69 Dart - 1.39 60 ft - 6.53 1/8 - 10.39 1/4
74 Challenger - 340
99 Dodge Ram - 360
|
racebeeper68
super gas
Reged: Jan 22 2003
Loc: Windsor ,Ca.
|
|
501" Mega block motor
some highlights of it include:
MP mega block (cross bolted mains)
Indy 440-1 indy heads hand ported by Angie of MEW (similar to the engine challenge motor)
gas ported and coated JE pistons
K1 rotating assembly (50 passes since new)
coated bearings
800 reliable HP built by Rich Nedbal and Mopar Engines West
Full detailed blue print to buyer
call or email for more info.
$12k or offer
707-974-2920
racebeeper68@sbcglobal.net
--------------------
 Richards Racing
2008 Infineon Super Pro Track Champion 
|
racebeeper68
super gas
Reged: Jan 22 2003
Loc: Windsor ,Ca.
|
|
Dodge / Plymouth stroked 400 drag race motor 451 cu. In.
72’ high nickel content block (B raised block)
440 Forged crank
Edelbrock performer heads ported by Wes King and finished off with titanium retainers and Comp Cams roller springs.
Arias forged pistons
12.5 / 1 comp. (108-110 octane fuel needed)
.662 lift roller cam
High volume oil pump
Your choice of 4500 or 4150 style intake manifold
Mallory distributor
Deep 7 quart pan / windage tray
sfi approved flex plate included
This motor was last freshened by Mopar Engines West 150 passes ago; I replaced it with a bigger motor to run low 9’s. This motor went a best of 9.68 @137 in my tube chassis Dodge Challenger. It had 80lbs of oil pressure and ran great when last ran. Local pick up located 1 hour north of San Francisco.
$4,500.
Call Keith @ 707-974-2920
--------------------
Richards Racing
2008 Infineon Super Pro Track Champion
|
1fast383
member
Reged: Jun 21 2005
Loc: mi.usa
|
|
A body wiper motor plates.3 in powder coat red,black and silver others will be polished also 1 a body heater blockoff plate. $10.00 each plus shipping. Email me at topendmachine@live.com THANKS MOPARTS FOR THE ADD!!!!!!! 
|
67mprfan
member
Reged: May 01 2005
Loc: ohio
|
|
8 3/4 posi center section 489 case 4:57 gear been sitting on my garage floor for 4yrs know time to go 450 obo 614-296-3653 edh1@wowway.com..........NO SHIPPING TO HEAVY....LOOK LIKE SMALL YOKE ON IT CAN MEASURE IF NEED BE
|
wesw
member
Reged: Jan 21 2007
Loc: iowa
|
|
mopar siamesed RB block. 4.53 bore, o-ring, set up for gear drive or jesel belt drive, 1/2 filled with hard block,cross-bolted main caps, the block has three sleeves in it. was a 580ci. the block is still in good shape. $800.00 OBO PENDING
callies 4.500 crank, standard mains 2.200 rods
less than 75 runs on the crank. $1500 OBO PENDING
set of R&R rod 7.100 .990 pin, 2.200. less than 30 passes on them. $700 OBO PENDING
off set distributor for a 440 complete cap rotor and MSD plug wires. $375. this is the same one INDY is selling for $795 .........SOLD.......
gary williams 1150 dominator carb. 9377 list
works great $550 FIRM
misc. dominator spacer plates 2 1/2" 2 1" $25ea.
simpson parachute (RED) pilot chute has some ware,
the chute is fine $75.00 SOLD.........
off-set roller lifters for big block. push rod oiling. like new only three runs on them. $250
LSM roller cam for large cube motor with 4/7 swap. this cam has three runs on it.
Cam ID# Z137
Cam Type CV8BB-45
Firing Order 1-8-7-3-6-5-4-2
Intake Exhaust
Lift .480 .480
[Email]Dur@50[/Email] 282 292
LCA 115
Install @ 115
Overlap 57
IVO 26 BTDC EVO 81 BBDC
IVC 76 ABDC EVC 31 ATDC
1.8 rotio rocker = .864 gross lift
1.7 ratio rocker = .816 gross lift
1.6 ratio rocker = .768 gross lift
half price of new........$300.00 PENDING
all parts are plus shipping
email me at sg5064@cox.net or call me at
712-256-6756 leave message if no answer.
thanks wes
Edited by wesw (Fri Nov 20 2009 03:12 AM)
|
pishta
mopar
Reged: Jun 21 2004
Loc: Tustin, CA
|
|
---------sold----------TY Moparts!------------
Edited by pishta (Mon Nov 09 2009 03:18 PM)
|
duster451
member
Reged: Jan 29 2006
Loc: ma
|
|
I have a pair of a-body superstock leaf springs with the long shocks.$175 obo 617-694-8007 dusterarea51@yahoo.com
|
duster451
member
Reged: Jan 29 2006
Loc: ma
|
|
I nave a set of 4.56 gears for a 8 3/4 rear for a 1 3/4 pinion.$50 dusterarea51@yahoo.com or 617-694-8007
|
ROSSIO
member
Reged: Feb 23 2009
Loc: dayton,ohio
|
|
complete carb to pan--ingrediance----
"1972" block .040 over-448cu in--bushed lifter bores
indy 440-1 alum heads 65cc-flow 393-1.5 indy rockers
indy intake--ross flat top pistonw/valve reliefs
scat rods(.990 pins/floating)-new eagle steel crank (std)
compcam (705 roller)comp lifters
milodon oil pan & ext. single line pickup
summit/ATI sfi damper & sfi plexplate
comes w/"dynamic" 5000 stahl motor convertor
'PRO SYSTEM"1050 dom.carb-MSDbillet dist w/wires
built by tony depillo(specialty motor works)
less than 30 pass-car ran [Email]10.35@129[/Email] 3350lb street legal dart-thru 4" exhaust 10.5 tire
$8500.00-obo--dayton,ohio
opt-headers & exhaust for sale too
RAMRACIN70@YAHOO.COM-or call 937-258-2520
--------------------
liv'n the mopar dream
Edited by ROSSIO (Sun Nov 08 2009 07:00 PM)
|
daytona5812
enthusiast
Reged: Nov 10 2004
Loc: Mn.
|
|
512 cu. in. Mopar
772 HP @ 6500
714 TQ @ 5000 w/110 race gas
76, 400 block-bored .035 sonic tested w/new alum main caps. Block has 1 sleeve
Crower custom made 4.25 crank 8-bolt
Manley H-beam 6.535 rods 2.200 ends
Ross flat top pistons 9.90 pins
Isky cam .660 lift 324 dur
Isky double valve springs
Crane 1.5 gold rockers w/chrome shafts. Lash caps
Pushrod Factory 3/8 pushrods
Cloyes true roller-chrome timing cover w/cam button
Lunati roller lifters - bronze dist drive
Charlies 8 qt dragster pan
Indy single line oil system
B1-BS w/ 2.200 IN. 1.810 EX. Ported & flowed by R-J performance. 352 @ .700 247 @ .700
Cometic head gaskets. ARP head & main studs.
Indy intake, match ported to heads.
Indy valve covers & valley plate. Tom Yancer breathers
Chuck Nuyten 1160 Dom
Fluidampr
Meizer water pump
MSD billet dist w/Accel 8.8 300+ wires
25 runs on re-fresh including new alum main caps, rings & bearings.
This motor ran 8.70 at 162 @ 2500 lbs.
9.90 @ 156 S/G
For a extra 200.00, I will re-dyno for buyer.
8500.00 FIRM. call 218-391-9696 or pm.
Thanks for the ad MOPARTS!!!
|
daytona5812
enthusiast
Reged: Nov 10 2004
Loc: Mn.
|
|
2
|
daytona5812
enthusiast
Reged: Nov 10 2004
Loc: Mn.
|
|
3
|
11sec68barracuda
super stock
Reged: Apr 07 2007
Loc: Glendale, Arizona
|
|
Holley 600 with electric choke. Vacuum secondaries. List number 80457-3. Just removed from car this morning. Runs excellent. Literally bolt on and go. Chrysler linkage adapter also available if needed. Asking $125. PM or e-mail AZmopar935@hotmail.com
--------------------
1968 Plymouth Barracuda fastback MM1
360/833/4.10 SG
1978 Plymouth Fury A38
E-58 360/904/3.21 SG
2001 Durango SLT
|
dragracer1
member
Reged: Jul 31 2008
Loc: Indiana
|
|
Post deleted by dragracer1
|
428RR
mopar
Reged: Dec 26 2007
Loc: east coast
|
|
I have a brand new holley 1000 carb never been mounted or gas though it. $625 shipped
|
dbran451
mopar
Reged: Nov 30 2003
Loc: ohio
|
|
I have a set of stage 6 heads I am taking off my Dart as I am steeping up to a set of B1.Heads. They are fully ported to max wedge size they have 214/181 valves with K motion 950 springs Crane gold rockers Mickey Thompson valve covers tall deck valley tray and an M1 intake for a tall deck. I am asking $2500 or best offer for every thing or I could separate if you don't need everything you can pm me here or e-mail at dbrannon@neo.rr.com
--------------------
1.393 60 ft. [Email]10.004@132.71[/Email]
Edited by dbran451 (Tue Nov 10 2009 05:22 PM)
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
