moparts
moparts
Reged: Jan 19 2003
Loc: Norwich CT USA
|
|
|
NOrrTH
member
Reged: Oct 02 2009
Loc: Nanaimo, BC
|
|
489 SureGrip with 3:73 or 3:91 in good condition
t-t@shaw.ca
--------------------
'71 GTX N96
|
gch
Polara Prince
Reged: Mar 06 2005
Loc: Angier,nc
|
|
Looking for an 8 1/4 OR 8 3/4 rear end for an A body.Something close to Raleigh NC preferred.
What you got?
PM or email in profile.
Thanks!
--------------------
You can't fix stupid
--------------------
70 polara 4dr 496/727/3.55 12.54 @ 107
96 vette lt4 coupe
83 honda v65 magna
|
Snoopy
moparts member
Reged: Mar 15 2003
Loc: So. Calif.
|
|
I need an original factory drive shaft for a 70 Cuda. 42.60" ctr-ctr for a BB/Dana car. Must be nice, straight and no dents or pits.
Please send a private message.
Thanks
|
gdonovan
Special 'K' in the haws!
Reged: Jun 13 2008
Loc: Oakdale CT
|
|
Just looking for a bare stock housing, unless you have a set of big bolt pattern axles too and I'll take them as well if the price is right.
Will consider a c-body unit for shortening.
garydonovan@hotmail.com
|
Commando1
member
Reged: Mar 16 2007
Loc: South-Central (Sebring), FL
|
|
FOUND!
Thank you.
Looking for a 3.55 gear set for the 9.25 rear.
|
R70RUNNER
Leg Lamp Lover
Reged: Aug 09 2005
Loc: Riverside, Ca
|
|
Looking for a 3.73 gear set (either 741 or 489)... have 3.91 (741) or 3.23 (489/29spline) to trade or buy outright. PM me here
--------------------
Moparts! Just like Myspace but WITHOUT the teen girls!
R70RUNNER<---VP Inland Empire Chapter of the MPM
|
68hemiss
mopar addict
Reged: Oct 29 2003
Loc: WI
|
|
I am looking for a stock set of 68-70 B-Body Dana 60 axles. Let me know what you have?
Mark J
|
MonGoo$e
master
Reged: Jan 20 2003
Loc: Corydon, Indiana
|
|
Looking for a Suregrip/Posi/LSD unit from an early 90's Dakota/Cherokee 8.25 (8 1/4) rear. Doesn't need ring gear or bearings on it, I just need a carrier unit for my '74 rear.
challyrally AT hotmail.com
I'm located in southern Indiana, 47172
thanks
-Adam
--------------------
1973 Plymouth Duster 318
1996 Dodge Dakota Sport 3.9
|
Drdotch
member
Reged: Nov 04 2006
Loc: New Mexico 87401
|
|
Need a 30 spline 8 3/4 spool
ASAP Thanks
|
62BT409
member
Reged: Feb 14 2007
Loc: Irwin, PA
|
|
I never realized how hard there little buggers are to find. Or I am just looking in the wrong place. I bought a housing and put everything in and thought I would wait to locate a breather. Now after looking everywhere, I can't find one. Am I calling it the right name? I see them for Chevy's
|
11sec68barracuda
super stock
Reged: Apr 07 2007
Loc: Glendale, Arizona
|
|
Looking for a 3-piece trans throttle pressure linkage setup for a small block. Need the throttle cable bracket, both bellcranks, and at least the top rod. I have the middle and bottom rod. Let me know what ya got. PM or e-mail AZmopar935@hotmail.com
--------------------
1968 Plymouth Barracuda fastback MM1
360/833/4.10 SG
1978 Plymouth Fury A38
E-58 360/904/3.21 SG
2001 Durango SLT
|
mopar_rr
member
Reged: Sep 06 2007
Loc: laurens,south carolina
|
|
I AM IN NEED OF ONE SPRING OUT OF AN OLD CONE TYPE POSI.ANYBODY HAVE AN OLD BROKE CONE TYPE I JUST NEED ONE SPRING.PLEASE LET ME KNOW HOW MUCH.ASAP THANKS MOPARTS 
mopar_gtx@prtcnet.com
--------------------
HAVE A NICE MOPARIN DAY....
|
SMILINJOE
mopar
Reged: Dec 13 2004
|
|
Looking for an A body 7 1/4
Must be in the Chicagoland area and cheap
Smilinjoe150@comcast.net
|
69MOPE
super gas
Reged: Jan 20 2003
Loc: Ridley Park, Pa.
|
|
I need 1 side gear for a 8 3/4 powerlock. e-mail me with a price if you have an extra one. nmpinnock@aol.com
Edited by 69MOPE (Thu Nov 19 2009 11:42 AM)
|
dustpan man
member
Reged: Sep 23 2007
Loc: littlestown pa
|
|
a sure grip,locker for my 83/4 489 case
|
sjm
member
Reged: Feb 13 2007
Loc: Michigan
|
|
Wanted 8-3/4 742 Case. Will prefer open with any gear
|
FC71Demon
member
Reged: Nov 11 2009
Loc: Bensalem PA
|
|
Looking for a 489 sure grip with 4.88 or 4.56 in good condition contact me at Fcviper3@aol.com with price
thanks
Fred
|
gdonovan
Special 'K' in the haws!
Reged: Jun 13 2008
Loc: Oakdale CT
|
|
Looking for a 3.21 or 3.55 ring and pinion set for 8.25"
garydonovan@hotmail.com
|
Jmlmc05
member
Reged: Jan 07 2008
Loc: Indlps,In
|
|
I have the 742 case if still looking complete with gear. $150+shipping Thanks Gary
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
